Safe Travels

By Troy Geisler06 September 2017

Safety on the job site is easy to recognize with hardhats, earplugs and blinding neon vests. But beyond the job site, when hauling construction equipment, components or vessels from one location to the next, how can safety be ensured? It all comes down to the load and the road.

Talbert 50 ton beam deck

Talbert 50 ton beam deck

Optimizing the safety of drivers and others when hauling large equipment begins long before the wheels start spinning – it must start at the very beginning of the transportation planning process. The first safety consideration should be choosing a trailer that is built for an operation’s specific load requirements. A trailer designed to handle the load safely eliminates the risk of structural failure as well as associated accidents and injuries.

When it comes to matching the trailer to the load requirement, capacity is a key criterion, but state laws and regulations, such as bridge laws and kingpin-to-axle distance guidelines, must also be factored. Generally, the load concentration, or the length of the deck that can handle the rated weight, is the main thing to keep

in mind.

A 26-foot, 50-ton lowbed can haul 50 tons, but how much of the deck those 50 tons occupy is just as important as the weight itself. One manufacturer might rate the entire length of the deck at 50 tons, while another might rate its trailer for 50 tons in a 16-foot span, and another that same weight in half the deck length.

Safety rating

In addition to load concentration, a trailer’s safety rating helps paint a more comprehensive picture of load capacity. A safety rating is an indicator of how much stress a trailer can safely handle. That stress comes from driving over uneven ground or off the road, hitting chuckholes, bouncing over bumps and crossing railroad tracks. Historically, magnification of payload weight on a trailer due to road dynamics is a 1.8 to 1 ratio. On average, the stress placed on a 50-ton-rated trailer by a 50-ton load when the rig hits those bumps, chucks and tracks equals 1.8 times 50 tons, or

90 tons.

It’s important to keep in mind that the 1.8 multiplier is only an average. On any given haul, the stress placed on the trailer can go above that level multiple times. If no cushion is built into the trailer to handle those spikes in stress, there will be more potential for long-term, progressive structural damage, which can lead to trailer failure off or on the road as well as diminish the life of the trailer.

Since there is no universal measure for safety ratings, they vary from manufacturer to manufacturer, from no margin to an industry high of 2.5 to 1, which is considered ample cushion.

A safety rating should never be used to determine how much weight can be added over the capacity rating and still keep the load, the driver and other drivers safe. In other words, a 2.5 to 1 safety rating on a 50-ton lowbed should not be used to justify loading a trailer with 125 tons of cargo.

It’s important to take trailer capacity seriously. Each time it’s overloaded, the dynamics of the steel changes, much like a rubber band. Eventually, the steel, and therefore the trailer, will break, increasing the risk for cargo damage, accidents and injuries.

Purchasing the right trailer can be complicated but many manufacturers know capacity from top to bottom and can help contractors select the best trailer for their application.

Talbert steel ibeam

For the most capacity and smallest impact on the trailer weight, some manufacturers use a T1 material with 100,000-psi minimum yield. T1 not only has maximum strength versus ductility, but also equates to a lighter, stronger trailer frame over other materials.

Pre-trip inspection

Whether it’s a custom trailer or standard unit, once it’s matched to the load, a pre-trip inspection should be done prior to taking off with each load.

Walk around the trailer and ensure there is no damage or cracks in the unit’s frame. Look for visible damage, such as chafed hydraulic hoses, which could spring a leak and cause the system to fail. Inspect tie-down equipment, such as chains, binders and straps, for broken parts and pieces and make sure they are rated appropriately. These ratings can be found on the equipment being hauled. Also ensure the trailer isn’t leaning or sagging to one side.

Check brakes and confirm the tires are properly inflated to the recommended psi. Overinflated or underinflated tires won’t have the proper load rating so

they won’t carry the weight like they should, which adds stress to the trailer. Traveling with improper tires also can cause a blowout when hauling heavy loads. Drivers can find the PSI, size, ply and load rating on the manufacturer’s VIN tag.

These are just some of the things to look for to ensure safe travels with heavy haul loads. There is a wide range of resources available that offer more information.

On the road

Safety is just as important on the road, too. In addition to state regulations, keep in mind trailers have a speed rating. Manufacturers usually state a 55 mph or 65 mph rating. The slower a rig travels, the less added weight or stress is placed on the trailer. The key is to purchase a trailer that will perform at a fleet’s normal operating speed.

From hardhats to load concentration, safety doesn’t stop at the job site. To ensure a successful project every time you must also consider the load, the road and everything in between.

Delivered directly to your inbox, World Crane Week Newsletter features the pick of the breaking news stories, product launches, show reports and more from KHL's world-class editorial team.
Latest News
An update on the North American tower crane market
Morrow Equipment President and COO Peter Juhren offers his ‘state of the union’ for the tower crane sector.
Susanek appointed Palfinger COO
A move from BMW sees Alexander Susanek take on chief operating officer role at Palfinger
What is the status of the North American crane market?
Three experts discuss market indicators – interest rates, inflation and the possibility of a recession.
D.Ann Shiffler Editor, American Cranes & Transport Tel: +1 512 869 8838 E-mail:
Matt Burk VP Sales Tel: +1 312 496 3314 E-mail: